How to Keep Earphone Thread from Tangling Using Embroidery Thread

news Publish tags Sources about us privacy
GratisForGratis

WikiHow

https://www.wikihow.it/Fare-in-Modo-che-il-Filo-delle-Cuffiette-non-si-Aggrovigli-Usando-del-Filo-da-Ricamo

If you're one of the millions of people tired of always finding your headphone cord tangled, there's a solution.No more spending hours trying to untangle cables.All you have to do is learn how to make a spiral bracelet and get some embroidery thread.
Part 1
Part 1 of 3:

Prepare the Headphones

Download PDF
  1. Step 1 Controlla che non vi siano cavi scoperti e danneggiati.
    Rather than spend the next 20-30 minutes trying to cover the cord with embroidery thread only to find it's broken, check its condition first.Throw away any broken pair of headphones and buy a new one.
  2. Step 2 Misura la lunghezza delle cuffiette, inclusi gli auricolari.
    This way you can get the right length of wire.
    Advertising
Part 2
Part 2 of 3:

Prepare the Thread

Download PDF
  1. Step 1 Taglia la lunghezza di filo necessaria secondo le misurazioni effettuate poc’anzi.
    Make sure you cut the thread without fraying it.
  2. Step 2 Fai un doppio nodo sui fili per legarli insieme.
    Consider starting at the base where the headphone plug is.
  3. Step 3 Stabilizza il filo delle cuffiette.
    Tie the wire to a clipboard to stabilize it or tape it to a flat surface.This way, we will prevent it from wandering around while we work.
    Advertising
Part 3
Part 3 of 3:

Wrap the Wire

Download PDF
  1. Step 1 Dividi in 3 il filo.
    • Division by three is recommended, but if you want you can divide it into several parts.
  2. Step 2 Intreccia.
    Cross the thread of one color with the thread of another color.After that, cross it under the third.Pull the thread through the loop and continue upwards.
  3. Step 3 Continua a intessere il cavo nella stessa maniera per altre 10-15 volte.
  4. Step 4 Prendi un altro filo colorato ed esegui la stessa operazione sopra gli altri fili..
    Hold the headphone wire in the middle so that it is completely wrapped around the wires.
  5. Step 5 Continua finché non arrivi ad un’estremità delle cuffiette.
    Choose one of the two earbuds and wrap the wire up to the base of the earbuds.After that, tie the thread with a double knot.
  6. Step 6 Ricomincia dal punto in cui il cavo delle cuffiette si divide e arriva fino all’altro auricolare.
    • Tie a double knot and begin wrapping the three strands together with the headphone cable in between.
    • Cut and tie the other end the same way as the first.Remove any excess thread
    Advertising

Advice

  • Coat the ends of the wires with a small amount of clear nail polish to prevent fraying.
  • Use this method on any other wires that get tangled easily.
  • Try adding a small layer of Scotch Guard to your headphones to make them more resistant to water and sweat.ATTENTION:this does not mean that you can immerse them in water
Advertising

Things you will need

  • New pair of headphones or old pair of headphones not tangled.
  • Embroidery thread of various colors, even up to three colors for the simplest knots;you'll need enough wire to triple cover the headphone cable you want to wrap.
  • Adhesive tape;After the initial knot, you will need to stabilize the earphones on a hard surface.
  • Clip to secure the headset wire to a clipboard (optional).
  • This guide is very useful for when you have to go on holiday and want to put your headphones in your suitcase without risking tangling the cable.
Licensed under: CC-BY-SA
CAPTCHA

Discover the site GratisForGratis

advertising

 

^