How to Turn a Soda Can into a Pipe

news Publish tags Sources about us privacy
GratisForGratis

WikiHow

https://www.wikihow.it/Trasformare-una-Lattina-di-Soda-in-una-Pipa

If you have something to smoke but no tools to do so, grab a can of soda and you'll be in luck.In fact, using a method worthy of Mac Guyver, you will be able to create a simple pipe or a more elaborate bong to smoke from without too many problems.Here are the different methods to follow.
Method 1
Method 1 of 2:

Making a Simple Pipe

PDF download Download PDF
  1. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    One of the 33 cl ones is fine, as are the half liter ones.Make sure it is completely empty and wash it with clean water.Let it dry before proceeding.
  2. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    You will need it to make small holes in the center, on the side of the can.Even a pen or pencil can be useful for this purpose.
    • If you don't have anything available, you could break the tab in half and use the sharp tip.
  3. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    Make sure that this cavity, where you will place the smoking material, is aligned with the mouth of the can, which you will use to inhale.
  4. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    Use a needle, pin, or other piercing tool to poke a series of holes in the space within the notch.The holes don't have to be big, but the more you make, the better.Create a brazier-shaped figure.
  5. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    Scrape away the paint on the surface of the cavity and adjacent areas, so as to eliminate much of the potentially harmful material which would be vaporized by smoking. Again use a sharp object or, if available, sandpaper.
  6. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    This will evaporate the chemicals used to coat the inside of the can.
  7. Watermark wikiHow to Trasformare una Lattina di Soda in una Pipa
    Choose the spot that feels most natural to cover with your finger while smoking, then use a sharp pencil or pen to pierce the can.
  8. Step 8 Ora puoi fumare.
    Place tobacco, or whatever you prefer to smoke, inside the cavity.Place your mouth on the mouth of the can, cover the hole you just created with your finger and use it as a "friction".Suck until the can is full and release your finger from the clutch when you're ready to inhale.
  9. Step 9 Sii consapevole dei rischi per la salute.
    It has been shown that heating and then inhaling aluminum can lead to Alzheimer's disease and other neurological diseases.Although it is difficult, with a simple lighter, to heat aluminum to a temperature that allows it to vaporize, it is still better not to joke about it.
    • The principle behind the pipe made from a can also applies to other widely available things like apples, potatoes, and other products that have no potentially harmful side effects.Smoke at your own risk.
Method 2
Method 2 of 2:

Making a Bong with Two Cans

PDF download Download PDF
  1. Step 1 Recupera tutto il materiale necessario.
    This is what you will need:
    • Two 33 cl cans
    • Adhesive tape
    • Can opener
    • Scissors
    • Trumpet mouthpiece
    • Waterfall
  2. Step 2 Taglia le estremità delle lattine.
    After washing and drying them, use the can opener to remove both ends from one of the cans, and just the top end from the other.Use the can opener the way you would normally open a can of soup, and remove any remaining ridges with scissors.You should now have one cylinder without both ends and one without the top, which will act as the base.[1]
  3. Step 3 Fai un buco nella lattina con ancora la base.
    In the side of the can, make a hole large enough to fit the mouthpiece of the mouthpiece, or whatever you want to use as a bowl.Using scissors, insert the mouthpiece and cover any remaining spaces with tape.
    • Make sure the edges are held together with a generous amount of tape.The mouthpiece must fit perfectly in the hole while remaining mobile so that it can be removed if necessary.Take all the time you need to apply the layers of tape in the best way.
  4. Step 4 Fissa con il nastro adesivo la lattina priva di estremità sopra quella con la base intatta.
    Join them with scotch tape to create the entire body of the bong.Pour in enough water so that the mouthpiece is slightly submerged.Now you are ready to smoke.
  5. Step 5 Fuma.
    Fill the bowl with whatever you like and pull through the top opening of the can.Once the bong is filled with smoke, remove the mouthpiece to inhale.

Advice

  • The hole in the side of the can should be no bigger than your finger can cover.In the first method, in fact, you will have to keep the hole plugged while you pull, then remove your finger and start inhaling.

Warnings

  • Smoking from a can is dangerous.Some of the chemicals present (aluminum, paint, plastic coatings) burn, releasing fumes that contain dangerous toxins.

Things you will need

  • Soda can
  • A needle, pin, awl, or ice chisel (or similar)
  • A sharp pencil, a pen, a thin screwdriver (or similar)
  • Fine grain sandpaper
  • Lighter
Licensed under: CC-BY-SA
CAPTCHA

Discover the site GratisForGratis

advertising

 

^